FasgearPCI-e 5.0 Extension Cable,16Pin(12+4) Male to PCI-E 5.0 3x8Pin Female Sleeved Extension Cable with 4 Cable Combs,30cm 12VHPWR(12V-2x6) Cable for GPU 3090Ti&RTX 4080 4090 5070 5080 16AWG

Bought this so I could connect 3 x PCIE 8 pin power feeds from my PC's power supply to my MSI Suprim 4080 graphics card. Does the job well, been in use for 4 moths - no problems. Very happy with it.

My geforce 4070TI card came with a faulty 12v power lead which seems to be known issue on the graphics card and this cable worked a treat to get the graphics card to power up and boot

Needed replacement for spider like cumbersome nvidia adaptor. Works fine with 300w and my 4080 FE. Definite click when plugged in. Would double check using with 4090 due to power required on load.

Great product better than the original one that came with the device good quality fits easy well worth the money

Ok i bought the 3 x 8 and 4 x 8 cables to see if both allowed a full 600W on my Asus TUF 4090.While the 3 x 8 works fine and pushed a full 600W to the card, for an extra couple of quid it might be worth going for the 4 x 8 as 600W split between four plugs will probably be better than three if you are running a 4090 with a 600W bios.For less powerful cards or those on a 450W Bios then this 3 x 4 pin is ideal and significantly better than the supplied nightmare Kraken of an adaptor.

i ordered this adapter in case of a wide rtx 4070 ti, but the pny one i ended getting had a receded 12vhpwr connector by 2cm and that left enough room for bending the original adapter in my narrow pc case which is has a clearance of 165mm, the card is 137mm wide, which left me with 48mm space, enough to bend the original adapter. i will keep the fasgear for any future need.

Seems to all work fine when I fitted and looks good plus quick delivery thanks

recommended !

I bought this in advance after buying my 4090 but before it got shipped in fear of all these reports of the default included NVIDIA adapter being hard to bend (I'm on a Fractal Meshify C case) and that bending it too much could cause issues.Well, with this cable the bends feel clean and very tolerant, so the cable stays at least 5 to 6mm away from my side panel and I'm not even bending it as much as I could.After 5 days of use, I have noticed no abnormalities and, although you are limited to 450W and no overclocking headrun because it uses only 3-8 pin connectors, the performance is mind-blowing. No need to overclock the GPU at this time for anything. Just for some context, I'm on an 850W Corsair RMx PSU and an i9-1050k.I took the extra precaution of limiting the GPU power to 80% just to be on the safe side; I've never seen the GPU go above 62 degrees, even on the most intensive games, benchmarks, or applications. At idle it hovers between 28-31 degrees with some light web browsing,I also have a cable from CableMod that goes straight from my PSU to the 600W plug on the card, I'm also planning on getting their angled adapter, just to be on the safe side.So far, this cable is doing its job and the cable my RTX 4090 FE came with is still in the box, unused.If you have spent the money and got a 4090 I would strongly recommend getting this cable, at least as a temporal solution to what could be an actual manufacturing issue from NVIDIA.

I have had the extension for some time now and I am satisfied with it. It works as intended and looks very good. Cable quality is also good.

Bei meiner Zotac 3090 TI war aus unerfindlichen Gründen der mitgelieferte 12vhpwr Adapter nach ca. 1 Jahr defekt, ein Kabelbruch. Also musste schnellstmöglich Ersatz her.Das gelieferte Kabel macht einen wirklich guten Eindruck was die Materialqualität und Verarbeitung angeht.Meine 3090 ti läuft mit dem Kabel jetzt mehrere Tage ohne Probleme, was die Langzeitnutzung angeht dazu kann ich natürlich noch nichts sagen.

Usato su una 4070ti Zotac per una gestione migliore dei cavi (lo spinotto è in mezzo alla scheda!!) e risultano molto buoni e precisi gli spinotti.